NOTE: Free essay sample provided on this page should be used for references or sample purposes only. The sample essay is available to anyone, so any direct quoting without mentioning the source will be considered plagiarism by schools, colleges and universities that use plagiarism detection software. To get a completely brand-new, plagiarism-free essay, please use our essay writing service.
One click instant price quote
Early work Rudolf web a German engineer, conceived the idea for the engine that now bears his name after seeking a device to increase the efficiency of the Otto engine. Diesel realized that the electric ignition process of the gasoline engine could be eliminated if, during the compression stroke of a piston-cylinder device, compression could heat air to a temperature higher than the auto-ignition temperature of a given fuel. Diesel proposed such a cycle in his patents of 1892 and 1893. Originally, either powdered coal or liquid petroleum was proposed as fuel. Diesel saw powdered coal, a by-product of the Saar coal mines, as a readily available fuel.
Compressed air was to be used to introduce coal dust into the engine cylinder; however, controlling the rate of coal injection was difficult, and after the experimental engine was destroyed by an explosion, Diesel turned to liquid petroleum. He continued to introduce the fuel into the engine with compressed air. The first commercial engine built on Diesel's patents was installed in St. Louis, Mo. , by Adolphus Busch, a brewer who had seen one on display at an exposition in Munich and had purchased a license from Diesel for the manufacture and sale of the engine in the United States and Canada. The engine operated successfully for years and was the forerunner of the Busch-Sulzer engine that powered many submarines of the U. S.
Navy in World War I. Another diesel engine used for the same purpose was the Nels eco, built by the New London Ship and Engine Company in Groton, Conn. The diesel engine became the primary power plant for submarines during World War I. It was not only economical in the use of fuel but also proved reliable under wartime conditions. Diesel fuel, less volatile than gasoline, was more easily stored and handled.
At the end of the war many men who had operated diesels were looking for peacetime jobs. Manufacturers began to adapt diesels for the peacetime economy. One modification was the development of the so-called semi diesel that operated on a two-stroke cycle at a lower compression pressure and made use of a hot bulb or tube to ignite the fuel charge. These changes resulted in an engine less expensive to build and maintain. Fuel-injection technology One objectionable feature of the full diesel was the necessity of a high-pressure, injection air compressor. Not only was energy required to drive the air compressor, but the sudden expansion of the air compressed to 6. 9 mega pascals when it entered the cylinder in which the pressure was only about 3. 4 to 4. 1 mega pascals resulted in a refrigerating effect that delayed ignition.
Diesel had needed high-pressure air with which to introduce powdered coal into the cylinder; when liquid petroleum replaced powdered coal as fuel, a pump could be made to take the place of the high-pressure air compressor. There were a number of ways in which a pump could be used. In England the Vickers Company used what was called the common-rail method, in which a battery of pumps maintained the fuel under pressure in a pipe running the length of the engine with leads to each cylinder. From this rail (or pipe) fuel-supply line, a series of injection valves admitted the fuel charge to each cylinder at the right point in its cycle. Another method employed cam-operated jerk, or plunger-type, pumps, to deliver fuel under momentarily high pressure to the injection valve of each cylinder at the right time.
The elimination of the injection air compressor was a step in the right direction, but there was yet another problem to be solved: the engine exhaust contained an excessive amount of smoke, even at outputs well within the horsepower rating of the engine and even though there was enough air in the cylinder to burn the fuel charge without leaving a discoloured exhaust that normally indicated overload. Engineers finally realized that the problem was that the momentarily high-pressure injection air exploding into the engine cylinder had diffused the fuel charge more efficiently than the substitute mechanical fuel nozzles were able to do, with the result that without the air compressor, the fuel had to search out the oxygen atoms to complete the combustion process, and since oxygen makes up only 20 percent of the air, each atom of fuel had only one chance in five of encountering an atom of oxygen. The result was improper burning of the fuel. The usual design of a fuel-injection nozzle introduced the fuel into the cylinder in the form of a cone spray, with the vapour radiating from the nozzle, rather than in a stream or jet. Very little could be done to diffuse the fuel more thoroughly. Improved mixing had to be accomplished by imparting additional motion to the air, most commonly by induction-produced air swirls or a radial movement of the air, called squish, or both, from the outer edge of the piston toward the centre.
Various methods have been employed to create this swirl and squish. Best results are apparently obtained when the air swirl bears a definite relation to the fuel-injection rate. Efficient utilization of the air within the cylinder demands a rotational velocity that causes the entrapped air to move continuously from one spray to the next during the injection period, without extreme subsidence between cycles. Price's engine In 1914 a young American engineer, William T. Price, began to experiment with an engine that would operate with a lower compression ratio than that of the diesel and at the same time would not require either hot bulbs or tubes.
As soon as his experiments began to show promise, he applied for patents. In Price's engine the selected compression pressure of nearly 1. 4 mega pascals did not provide a high enough temperature to ignite the fuel charge when starting. Ignition was accomplished by a fine wire coil in the combustion chamber. Nichrome wire was used for this because it could easily be heated to incandescence when an electric current was passed through it. The experimental engine had a single horizontal cylinder with a bore of 43 centimetres and a stroke (maximum piston movement) of 48 centimetres and operated at 257 revolutions per minute. Because the nichrome wire required frequent replacement, the compression pressure was raised to 2. 4 mega pascals, which did provide a temperature high enough for ignition when starting.
Some of the fuel charge was injected before the end of the compression stroke in an effort to increase the cycle timing and to keep the nichrome wire glowing hot. In the meantime many engines of the two-stroke cycle, semi diesel type were being installed. Some were used to produce electricity for small municipalities, while others were installed in water pumping plants. Many provided power for tugs, fishing boats, trawlers, and workouts. In the early 1920 s the General Electric Company suggested to the Ingersoll-Rand Company, for whom Price was working, that they cooperate in the building of a diesel-electric locomotive. At that time many of the locomotives in service were powered by gasoline engines.
A diesel-electric locomotive with Price's engine was completed in 1924 and placed in service for switching purposes in New York City. The success of this locomotive resulted in orders from railroads, factories, and open-pit mines. The engine used in most of these installations was a six-cylinder, 25 -centimetres bore, 30 -centimetres stroke system, rated 300 brake horsepower at 600 revolutions and weighing 6, 800 kilograms. Subsequent developments and applications Many diesel engines were purchased for web marine propulsion. The diesels, however, normally rotated faster than was desirable for the propellers of large ships because the high speeds of the huge propellers tended to create hollowed-out areas within the water around the propeller (cavitation), with resultant loss of thrust. The problem did not exist, however, with smaller propellers, and diesel engines proved especially suitable for yachts, in which speed is desired.
The problem was solved by utilizing a diesel-electric installation in which the engines were connected to direct-current generators that furnished the electricity to drive an electric motor connected to the ship's propeller. There were also many installations in which the diesel was connected either directly or through gears to the propeller. When diesel engines of larger horsepower and slower rotation speeds became available, they were installed in cargo and passenger ships. The diesel engine became the predominant power plant for military equipment on the ground and at sea during World War II. Since then it has been adopted for use in heavy construction machinery, high-powered farm tractors, and most large trucks and buses. Diesel engines also have been installed in hospitals, telephone exchanges, airports, and various other facilities to provide emergency power during electrical power outages.
In addition, they have been used in automobiles, albeit on a limited scale. Although diesels provide better fuel economy than gasoline engines, they do not run as smoothly as the latter and emit higher levels of pollutants. Major types of diesel engines There are three basic size groups of diesel engines based on power -- namely, small, medium, and large. The small engines have power output values of less than 188 kilowatts, or 252 horsepower. This is the most commonly produced diesel-engine type. These engines are used in automobiles, light trucks, and some agricultural and construction applications, and as small stationary electrical power generators (such as those on pleasure craft) and as mechanical drives.
They are typically direct-injection, in-line, four- or six-cylinder engines. Many are turbocharged with after coolers. Medium engines have power capacities ranging from 188 to 750 kilowatts, or 252 to 1, 006 horsepower. The majority of these engines are used in heavy-duty trucks (those of the class 6, 7, and 8 variety). They are usually direct-injection, in-line, six-cylinder turbocharged / after cooled engines. Some V- 8 and V- 12 engines also belong to this size group.
Large diesel engines have power ratings in excess of 750 kilowatts. These unique engines are used for marine, locomotive, and mechanical drive applications and for electrical power generation. In most cases, they are direct-injection, turbocharged / after cooled systems. They may operate at as low as 500 revolutions per minute when good reliability and durability are critical.
Free research essays on topics related to: diesel engines, power plant, compressed air, electrical power, high pressure
Research essay sample on Diesel Engines High Pressure
