NOTE: Free essay sample provided on this page should be used for references or sample purposes only. The sample essay is available to anyone, so any direct quoting without mentioning the source will be considered plagiarism by schools, colleges and universities that use plagiarism detection software. To get a completely brand-new, plagiarism-free essay, please use our essay writing service.
One click instant price quote
Recently in a local hearing clinic, a clients concerns were discussed. Im afraid I wont like them. My brother in law bought two hearing aids, and he keeps them in a drawer in the kitchen. While the number of people dissatisfied with their hearing aids hovers around 50 %, the hearing aid industry is hard pressed to decrease the number of returns, and increase the average daily use of each aid. In order to accomplish this, hearing aid manufacturers must answer the most often heard complaint: It doesnt work well in noise. Unfortunately, a hearing aid will never be able to accomplish the sifting and sorting that is carried out in the human brain.
While a person with normal hearing sits in a restaurant, he can distinguish a conversational speech signal that is as little as three decibels greater than the ambient noise. On the other hand, a person with a 30 -decibel sensori neural loss might need the speech signal to be 15 or more decibels greater than the ambient noise. The hearing aids task is to acoustically or electronically compensate for both the neurological shortcomings of the hearing impaired person and the wide band increase inherent in any basic amplifier. Acoustic compensation can be carried out in a hearing aid microphone.
Most hearing aids today utilize omnidirectional microphones, which pick up sound equally from all directions. This may be beneficial and practical in some cases, as in the completely in the canal (CIC) aid. The CIC aid uses the natural funneling of the auricle in order to focus sound directly into the instrument. Behind-the-ear (BTE) and full concha in-the-ear (ITE) aids lose this anatomical feature, and may benefit from a directional microphone. The purpose of using a directional microphone is to focus its sensitivity toward the front of the listener, thereby attenuating or reducing unwanted noise or competition emanating from behind the listener. (Search 1998) Microphone directionality can be accomplished by using a single microphone with two sound inlets. In this mechanical method, the time lag created by a sound entering each inlet is precisely calibrated to cancel out sounds from the sides and back of the microphone as they strike the diaphragm.
The Phonak Micro Zoom&# 61668; uses an electronic approach. Each Micro Zoom&# 61668; contains two omnidirectional microphones. According to the flyer, One picks up sound in front of you while a second picks up sound from the sides and rear. A tiny computer chip inside the aid analyzes both sounds.
It then enhances the sound from the front, and reduces background sounds from the sides and rear. (Phonak 1997) In reality, the tiny computer is analyzing the time it takes for a sound to reach each microphone and mathematically decreasing ALL sounds from the sides and rear, speech included. Directional microphone technology is fallible in one regard: it assumes that all noise is spatially related. Unfortunately, much of the noise present in our environment is omnidirectional. Even though significant benefit can be achieved by sound focusing, a directional aid also must perform in an environment with multiple speakers situated around a listener, combined with noise from high priority directions. Signal processing, or digital signal processing (DSP), is partly utilized in amplification in order to narrow the focus from all sounds to speech sounds. A linear aid will amplify all frequencies equally, limited to the characteristics of the input / output transducers and the coupler type.
On the other hand DSP aids can alter the frequency response of an aid based on their design and / or programming. There are many techniques that can be used which are based on type of loss, but since speech encompasses such a wide frequency range, audiologists need to choose wisely which type of processing to use. Minimally, signal processing for noise reduction is analogous to a continually adjusting graphic equalizer for a home stereo system. Level dependent frequency response (LDFR) hearing aids can also adjust their equalizer settings based on input volume. Along with standard fitting techniques, subjective client opinions are one of the most important factors in decreasing hearing aid returns. In the past several years, technological advances have given audiologists several options.
One such LDFR hearing aid incorporates BILL (bass increase at low levels) circuitry. If it were assumed that most detrimental noise occurs in the low frequencies, then decreasing the low frequency response of a hearing aid at high levels would reduce noise and improve a persons speech discrimination performance score. This concept seems natural based on the upward spread of masking principle. Since a low frequency sound must travel farther up the basilar membrane, it will mask out a competing higher frequency sound that does not have to travel as far.
By reducing low frequency sounds at high levels, a hearing aid could minimize the upward spread of masking, and allow for increased speech reception. According to one study, while it is reasonable to assume that BILL circuitry would be beneficial in the presence of low frequency noise, there is no evidence that listeners with hearing loss exhibit increasing amounts of upward spread of masking with increasing level. (Bacon, et. al. 1997) Another study shows that while there is a significant difference between unaided performance and BILL aided performance in noise, there was no significant difference between BILL processing and linear processing. (Bess et. al. 1997) Since both studies showed no detriment or reduction in speech scores while using BILL processing, it is reasonable to assume that this type of processing would be beneficial if the client perceives better sound quality as a result. In contrast, TILL processing or Treble Increases at Low Levels, provides a low frequency signal reduction at low intensities. This type of device is based on the premise that hearing-impaired subjects have normal growth of loudness for high level stimuli; therefore, intense sounds should be acoustically invisible, and thus not amplified. (Bess et.
al. 1991) This type of circuit is employed by the K-Amp&# 61668; (Etymotic Research), which is used to decrease loudness discomfort associated with high level, high frequency sounds. The K-Amp&# 61668; rationale assumes that most hearing-impaired listeners have greater hearing loss in the high frequencies than in the low frequencies and, therefore, require high-frequency emphasis amplification. (Valente 1996) Proponents of the TILL circuitry believe that by reducing low frequency sounds at low levels, the hearing aid inherently has a high frequency emphasis, and will therefore promote better speech reception in noise while maintaining a more natural fidelity. Initially, BILL and TILL seem to be direct opposites, however an insertion gain frequency curve (Bess et. al. 1991) shows that both algorithms provide significant high frequency gain at low levels. With a 50 -decibel broad band noise, the BILL hearing aid shows a 10 to 20 dB boost through the low to mid frequencies. At 90 decibels of input, the BILL aid reduces the low frequencies completely, while still providing gain in the high frequencies.
The insertion gain frequency curve shows that this type of circuit may not be beneficial for a client with a limited dynamic range. Conversely, the TILL hearing aid shows limited bass boost and significant treble boost with a 50 decibel broad band noise. At 90 decibels of input however, the TILL hearing aid shows a relatively flat response, in retort to the belief that little or no amplification should be necessary at that high intensity. The BILL and TILL hearing aids are both effective with varying types of hearing losses, but this type of noise reduction is contingent on the fact that noise perception can be changed by varying the frequency response of an amplifier. For the majority of hearing aids, this is only a limited means of changing how well a client can understand speech in noise. Each client however, will have varying degrees of subjective opinions regarding the function of their aid.
While acoustic modifications such as venting and mechanical filtering can be made in order to change sound quality, the BILL and TILL hearing aids, once chosen are adjustable only to the limits of their programming. The PILL circuit (Programmable Increases at Low Levels) affords the clinician more possibilities wh...
Free research essays on topics related to: hearing aids, significant difference, hearing impaired, signal processing, low levels
Research essay sample on Noise Reduction In Hearing Aids
