NOTE: Free essay sample provided on this page should be used for references or sample purposes only. The sample essay is available to anyone, so any direct quoting without mentioning the source will be considered plagiarism by schools, colleges and universities that use plagiarism detection software. To get a completely brand-new, plagiarism-free essay, please use our essay writing service.
One click instant price quote
... eating, AUTO, automatically loads these device drivers. The AUTO setting also automatically uses the BUFFERSHIGH, FILESHIGH, FCBSHIGH, LASTDRIVEHIGH, and STACKSHIGH commands, whether the -HIGH form of the command is used or not. If you specify the NOAUTO parameter, you must load these device drivers and use the -HIGH form of the above commands in order to take advantage of them.
This command defines parameters for devices such as disk and tape drives when you start MS-DOS. You can use this command The DRIVPARM command modifies the parameters of an existing physical drive. It does not create a new logical drive. The settings specified in the DRIVPARM command override the driver definitions DRIVPARM = /D: number [/C] [/F: factor] [/H: heads] [/I] [/N] Specifies the physical drive number. Values for number must be in the range 0 through 255. For example, drive number 0 = drive A, 1 = drive B, 2 = drive C, and so on.
Specifies that the drive can detect whether the drive Specifies the drive type. The following table shows the valid values for factor and a brief description of each. 7 1. 44 MB (3. 5 -inch disk) 8 Read / write optical disk 9 2. 88 MB (3. 5 -inch disk) Specifies the maximum number of heads. Values for heads must be in the range 1 through 99. The default value depends on the value you specify for /F: factor. Specifies an electronically compatible 3. 5 -inch floppy disk drive. Use the /I switch if your computer's ROM BIOS does not support 3. 5 -inch Specifies a non removable block device.
Specifies the number of sectors per track that the block device supports. Values for sectors must be in the range 1 through 99. The default value depends on the value you specify for /F: factor. Specifies the number of tracks per side that the block device supports.
The default value depends on the value you specify for /F: factor. This command specifies the number of file control blocks (FCBs) that MS-DOS can have open at the same time. Use the FCBSHIGH command to load the FCBs in the upper memory area. You can use these commands only in your Config. sys file. Specifies the number of file control blocks that MS-DOS can have open at one time.
Valid values for x are in the range 1 through 255. The default This command specifies the number of files that MS-DOS can access at one time. Use the FILESHIGH command to load the command in the upper memory area. You can use these commands Specifies the number of files that MS-DOS can access at one time. Valid values for x are in the range 8 through 255. The default value is 30.
This command loads a memory-resident program into memory when you start MS-DOS. Use the INSTALLHIGH command to load the memory-resident program into the upper memory area. You can use these commands only in Memory-resident programs stay in memory as long as your computer is on. They can be used even when other programs are active. You can use the INSTALL or INSTALLHIGH command to load MS-DOS memory-resident INSTALL = [drive: ][path]filename [command-parameters] INSTALLHIGH = [drive: ][path]filename [command-parameters] Specifies the location and name of the memory-resident program you want to run. Specifies parameters for the program you This command specifies the maximum number of drives you can access.
Use the LASTDRIVEHIGH command to load the LASTDRIVE data structures in the upper memory area. You can use these commands only in your Config. sys file. The value you specify represents the last valid drive that MS-DOS is to recognize. Specifies a drive letter in the range A through Z. This command specifies whether the NUM LOCK key is set to ON or OFF when your computer starts.
You can use this command only in If set to ON, turns on the NUM LOCK key when MS-DOS displays the startup menu. If set to OFF, turns This command enables you to include comments in a batch file or in your Config. sys file. The REM command is also useful for disabling commands. You can use a semicolon (; ) instead of the REM command in your Config. sys file, but not in batch files.
Specifies any string of characters, for example, the command you want to disable or the comment This command displays, sets, or removes MS-DOS environment You use environment variables to control the behavior of some batch files and programs and to control the way MS-DOS appears and works. The SET command is often used in the Auto exec. bat or Config. sys files to set environment variables each To display the current environment settings at the command prompt, use the following syntax: Specifies the variable you want to set or modify. Specifies the string you want to associate This command specifies the name and location of the command interpreter you want MS-DOS to use. You can use this command If you want to use your own command interpreter instead of Command.
com, you can specify its name by adding a SHELL SHELL = [[drive: ]path]filename [parameters] Specifies the location and name of the command interpreter you want MS-DOS to use. Specifies any command-line parameters or switches that can be used with the specified command interpreter. This command supports the dynamic use of data stacks to handle hardware interrupts. Use the STACKSHIGH command to load the stacks in the upper memory area. You can use these commands Specifies the number of stacks. Valid values for n are 0 and numbers in the range 8 through 64.
Specifies the size (in bytes) of each stack. Valid values for s are 0 and numbers in the range This command specifies special options in MS-DOS. Use this command only in your Config. sys file.
Forces an enhanced keyboard to behave like a Prevents you from using the F 5 or F 8 key to bypass startup commands. (SWITCHES /N does not prevent you from pressing CTRL+F 5 or CTRL+F 8 to bypass Drv space. bin or Dbl space. bin; to prevent this, use the D SPACE /SWITCHES command to add the SWITCHES /N setting to your Used without the: n parameter, indicates that Io. sys should suppress the automatic relocation of EBIOS. (Automatic relocation of EBIOS increases the conventional memory available to MS-DOS-based programs. ) Suppressing automatic relocation results in less conventional memory available to MS-DOS-based programs. Use the /E switch with the n parameter to relocate N bytes of EBIOS to low memory, where n is the number of bytes to be relocated. The minimum value for n is 48 and the maximum value is 1024.
The number specified is always rounded up to the next multiple You can find more information on MS-DOS commands on your Windows 98 Second Edition CD-ROM. Open the file Bibliography:
Free research essays on topics related to: commands, ms dos, command, config sys, dos
Research essay sample on Config Sys Ms Dos
